Crossover & Hard Pipe

TECHNICAL DATA Why not add top alloy boost pipe kit for just £129.95 which includes 2 x alloy boost pipes, 1 x silicone joiner and stainless jubilee clips. Fits Citreon DS3, Peugeot 207 GTI, Peugeot 208 GTI. Part no: ATINTP&C4

Read more less

AIRTEC Motorsport cold side boost pipes for Renault Clio 200 / 220 EDC. To replace the standard plastic pipes, known to fail! Features of cold side: Bigger diameter pipe onto the throttle body, AIRTEC pipe 63.5mm compared to standard 60mm. To replace the standard plastic pipes known to fail due to heat soak, standard pipes are known to blow off and cause a loss of boost. Will fit all intercooler kits, designed to follow standard path. Registered Design Right number: 6030033

Read more less

AIRTEC Motorsport Lower De-Res Pipe for Focus MK3 ST-D Designed to increase airflow on the Focus MK3 ST-D as a replacement of the restrictive standard boost pipe, the AIRTEC Motorsport boost pipe creates a much smoother air flow by replacing the restrictive bends and smaller diameter pipe. AIRTEC Part No: ATMSFO120 TECHNICAL DATA AIRTEC Motorsport Lower De-Res Pipe for Focus MK3 ST-D Designed to increase airflow on the Focus MK3 ST-D as a replacement of the restrictive standard boost pipe, the AIRTEC Motorsport boost pipe creates a much smoother air flow by replacing the restrictive bends and smaller diameter pipe. Features: Swaged ends to prevent pipes working loose on bigger power cars. Will work perfectly with standard or re-mapped STs. To fit with both, stock and upgraded AIRTEC intercooler. Resonator delete. Fitting takes less than 30 minutes to install and fits to standard boost hoses. 47mm pipe throughout. Available in Pro-Series Black. AIRTEC Part No: ATMSFO120

Read more less

A direct replacement part that gives increases in response and sound by eliminating the internal sound resonators built into the original boost pipe from the turbo. The manufacturer fits these resonators to reduce noise and quieten the tone, but by replacing the pipe for one without the baffled internals, flow is improved, as well as noise. This increases throttle response and heightens the soundtrack from within the car. The pipe is made from high-quality aluminium with a machined connector to fit the original fitting and is finished in powder coated black with a laser-cut plaque. The installation package includes all fixtures and fittings, as well as detailed installation instructions. With valuable performance gains and an improved soundtrack, the AIRTEC Motorsport de-res pipe kit is an essential modification. Features: Increases response and sound Improves flow from turbo Direct replacement fitment High quality aluminium construction Powder coat black finish Includes all fixtures and fittings Features detailed fitting guide Fitment: BMW 1 Series – F52 – (10/2015 to 12/2019) BMW 1 Series – F44 Gran Coupé – (10/2018 to 12/2019) BMW 1 Series – F45 Active Tourer – (11/2013 to 04/2018) BMW 1 Series – F45 Active Tourer LCI – (05/2017 to 12/2019) BMW 1 Series – F46 Gran Tourer – (07/2014 to 03/2018) BMW 1 Series – F46 Gran Tourer LCI – (05/2017 to 12/2019) BMW X1 – F48 – (11/2014 to  06/2019) BMW X1 – F48 LCI – (05/2018 to 01/2020) BMW X1 – F49 – (11/2014 to 08/2019) BMW X1 – F49 LCI – (05/2018 to 12/2019) BMW X2 – F39 – (10/2016 to 12/2019) MINI F56 – (04/2013 to 12/2019) MINI F55 – (09/2013 to 12/2019) MINI Clubman F54 – (11/2014 to 07/2019) MINI Clubman F54 LCI – (05/2018 to 12/2019) MINI Cabriolet F57 – (11/2014 to 12/2019) MINI Countryman F60 – (11/2015 to 01/2020)  Only in Pro-Series Black, silver for photo purposes only.  AIRTEC part no: ATMSMINI15

Read more less

A direct replacement part that offers increases in performance and response, the enlarged turbo inlet elbow features a freer-flowing design with an increased internal diameter. AIRTEC Part No: ATMSYGR08 TECHNICAL DATA As part of our expanding Yaris GR product range, AIRTEC Motorsport is proud to launch our enlarged turbo inlet elbow upgrade suitable for track or fast road use. A direct replacement part that offers increases in performance and response, the enlarged turbo inlet elbow features a freer-flowing design with an increased internal diameter. How it worksThe original elbow gradually tapers down from the 63mm induction pipe to just 48.5mm as it enters the turbo, despite the turbo’s inlet measuring 51mm in diameter. This causes an unnecessary restriction within the intake side that hampers flow and limits throttle response. Our AIRTEC Motorsport direct replacement elbow features a CNC-machined flange with a correctly matched 51mm diameter, therefore removing the stepped restriction. The high-quality silicone hose instantly tapers to meet the 63mm diameter intake, therefore allowing the maximum amount of internal flow with increases of nearly 10%. The elbow upgrade includes all fixtures and fittings, as well as detailed instructions. The increased volume and improved design works to reduce restriction and improve flow to the turbo, providing an increase in power and response. Please note: this part will not fit with a Turbosmart uprated blow-off valve in place.  Specification: Up to 10% increase in bore size Larger, freer-flowing design Improves airflow to the turbo Increases throttle response Direct replacement fitment Includes all fixtures and fittings Features detailed fitting guide   AIRTEC Part No: ATMSYGR08

Read more less

As part of our expanding Yaris GR product range, AIRTEC Motorsport is proud to launch our big boost pipe kit upgrade suitable for track or fast road use. AIRTEC Part No: ATMSYGR06 TECHNICAL DATA As part of our expanding Yaris GR product range, AIRTEC Motorsport is proud to launch our big boost pipe kit upgrade suitable for track or fast road use. A direct replacement kit that offers increases in performance and response, the enlarged boost pipe kit features a freer-flowing design with a increased internal diameter on both the hot side and cold side. Cold SideOur comprehensive eight-piece kit begins with a gentle taper from the 40mm turbo outlet that increases by 25% to reach 50mm as it meets the AIRTEC Motorsport intercooler inlet side. Hot SideFrom the intercooler’s 60mm outlet side, the pipework tapers back down to meet the throttle body’s 49.5mm size, maintaining a 53mm minimum as it reaches the new cast alloy throttle body elbow. In doing so, it offers up to a 39% increase in internal diameter during the most restrictive part of the OEM pipework (38mm) just before the throttle body elbow. This increased overall internal volume and improved design works to reduce restriction and improve flow from the turbo and to the inlet, providing an increase in power and response. Made from high quality aluminium, the kit includes a revised throttle body elbow, a series of high-quality silicone connectors and all pipework is finished in powder-coated black for a subtle OEM+ look. The installation package includes all fixtures and fittings, and detailed instructions. With valuable performance gains and an improved look to the engine bay, the AIRTEC Motorsport enlarged boost pipe kit is an essential modification. Specification: Up to 39% increase in bore size Larger and freer-flowing design Comprehensive eight-piece kit Improves flow from the turbo to the inlet Increases mid-range performance Direct replacement fitment Made from high quality alloy Powder-coated black finish Includes all fixtures and fittings Features detailed fitting guide Please note: Will not fit OEM intercooler – designed only for use with AIRTEC Motorsport intercooler upgrade.  AIRTEC Part No: ATMSYGR06

Read more less

TECHNICAL DATA The 2.5″ big boost pipe kit is a must for all remapped Volvos. Everything you need is included in the kit. Our 2.5″ hard pipe upgrade removes the 2.0″ restrictive boost pipes. We saw gains of 11.8 bhp & 9 lb/ft torque increases over the standard Ford pipes and these gains were achieved by simply bolting on the kit. Features: Hot side (turbo to intercooler) is made from 2.5″ light-weight alloy and connected with 5 ply silicone hose joiners. NEW! Now comes with 70mm coldside hose to fit standard size throttle body expanding up to 70mm Please Note: This is a Symposer Delete Item Will fit With the following intercoolers AIRTEC Pace Pro-Alloy Forge Ford OEM Direct replacement! No modding required. This kit is designed for bigger power cars. All pipes have swaged ends to stop the pipes blowing off. Please note: Custom colours are made to order, please expect a 5-10 day delay on custom colours. Peak show times may be a longer 7-10 day delay. Fitting takes 1 – 2 hours. Please Note: Pipework only available in silver. Registered Design Right number: 6044469 Gloss Black, Race Red, Performance Blue normally kept in stock, please allow 3-5 working days for delivery. Other colour hoses, made to orderFrozen White, Bright Yellow, Grey, Kawasaki Green, Orange,Purple, Vivid Pink, Nitrous Blue, Ultimate Green, Nitrous BluePlease allow 2-4 weeks for delivery.

Read more less

TECHNICAL DATA AIRTEC Motorsport Stage 1 Uprated Big Boost Pipes for the Mini F56 John Cooper Works. A must for all tuned examples, our larger boost pipes offers improved flow with less restriction over the car’s original boost pipes. All connectors have swaged ends to stop the pipes blowing off under pressure. Includes three metal hard pipes, one hose joiner and two Pro Hoses silicone hoses. Available in Motorsport Silver and with Black, Blue and Red silicone hose colours to choose from. Designed to fit with our AIRTEC uprated intercooler only.

Read more less

TECHNICAL DATA AIRTEC has now added a great addition to it’s growing range of performance intercoolers, in the way of this huge front mount for the Peugeot RCZ 1.6 Turbo. Great addition to any standard, or remapped, RCZ. Features 60mm thick track proven Bar and Plate core, specked to AIRTEC design AIRTEC cast end tanks for improved airflow and unbeatable strength Comes with silicone and alloy boost pipe connecting hoses – includes stainless clips Fitting takes less 2-3 hours, comes with fitting instructions 3 year unlimited mileage warranty Available in Pro-Series Satin Black or Natural Silver AIRTEC logo available at no extra charge Huge surface area, but still allows plenty of airflow to top section of the radiator, which is essential for hotter climate countries Approximate dimensions: 60mm thick 175mm height 760mm width  

Read more less

TECHNICAL DATA Why not add top alloy boost pipe kit for just £129.95 which includes 2 x alloy boost pipes, 1 x silicone joiner and stainless jubilee clips. Fits Citreon DS3, Peugeot 207 GTI, Peugeot 208 GTI. Part no: ATINTP&C4

Read more less

AIRTEC Motorsport big boost pipe kit for a Meglio (Megane turbo powered Clio) Designed to directly replace the original boost pipes and hoses with larger and freer flowing 50mm AIRTEC Motorsport hard pipes and Pro Hoses silicone connectors. This complete kit creates an easy, simple upgrade solution for a Renault Megane turbo converted Clio. Fits Clio 197 without factory air-con fitted (or air-con delete kit fitted). Comes complete with 2x hard pipes and 4x Pro Hoses silicone connectors. WILL FIT WITH STOCK MEGANE INTERCOOLER

Read more less

AIRTEC Motorsport hot side boost pipe for Renault Clio. now only available in black Features of hot side: Designed to increase air flow with no kinks and a less restrictive pipe – To fit standard and AIRTEC intercooler kits Will not fit with Ultra racing strut brace (Will require spacers) Only available in Pro-Series Black

Read more less